2.2KW ER20 D80 110V Air cooled spindle motor 4pcs ceramic ball bearings (110, Volts (AC))

Price: $252.60
(as of Dec 16,2024 14:54:28 UTC – Details)

Product Description

Basic parameter

Size: 80*224mm

Cooling: Air cooling Power: 2.2KW

Voltage: 110v

Current: 20A

Frequency: 400Hz

Speed: 0-24000rpm

Runout Off: Less than 0.01mm

Diameter: 80mm

4 PCS Fully sealed angular contact bearings

Collet: ER20

Grease Lubrication

We are the spindle manufacturer,we use better material to produce the spindle.

1.We use steel bearings seat,spindle will not morph during the using life.Increase the spindle using life.

2.We use 4 pcs 7 series fully sealed angular contact ball bearings, it quality much better, usually use it 1-2 years without any problems.

3. Full power spindle, stronger shaft and coil,more power in engraving and cutting working.

4. Precision 0.01mm.Coaxial degree less than 0.0025mm,suitable for high accuracy work.

5. Carefull assembly make the spindle more precisional. 3-4 hours testing after assemble, 99.9% pass rate. No worry after ordering.

6. We work with biggest CNC router manufacturer in USA, EU,RU. Strong work partners.

If the spindle will not be used for a long time, please keep the spindle oil sealed to prevent rust from being unused for a long time. Before shipping , we did the oil seal to avoid the rust during the long shipment. When you get the spindle, please clearing the oil seal before using. Thank you.

Water cooled spindle MUST be used with water pump. Otherwise the spindle will soon broken.

AC spindle motor MUST use with inverter. The power of inverter need equal or bigger than the spindle power. Before using,please set up the inverter parameters suitable for spindle. Otherwise the spindle and inverter will broken at once.

When you use the spindle,the noise is not same as always,please STOP the spindle at once. You may need to replace the spindle bearings.

Spindle in the preservation and transportation, high-speed grease inside the bearing state will change, customers should be running at low speed for 30 minutes. 3000 rpm and then follow the poor increase, run 20 minutes each. Spindle and the inverter should be working together. The inverter’s specifications and parameter settings need match spindles parameter.(Because of high-speed grease inside the bearing state will change,when you get the spindle, maybe the noise sounds not normal.Please run it 30 minutes or even more, the noise will be normal.)
Connect the inverter spindle, three-phase inverter power cord should be soldered in the plug 1 (U), 2 (V), 3 (W) feet, 4 feet for the ground. After the power is turned on, to observe whether the spindle rotation axis indicates the direction consistent. If inconsistency should be immediately shut down, replace the inverter and spindle connected two wires of three-phase power supply.
During normal operation, air-cooled spindle often encounter the phenomenon of heat, always check whether the air-cooled spindle housing and duct clogging dust.If clogging dust, to promptly clean up. If you do not clean up, it is easily to make the spindle burned.
Every day before using the spindle must be running at low speed for 15-20 minutes. Clamping the cutters to spindle, collet nuts ,collets,cutters must be clean enough. Shank inserted into the collet must be greater than 15mm.

AC 110V spindle motor (Must need connect to inverter/VFD)
4pcs 7 series angular contact bearing, exterd the spindle using life.
Spindle connect to GND, Pin-4 connect to inverter GND.
Spindle 1-2-3, connect to inverter U. V. W.

Introducing the 2.2KW ER20 D80 110V Air cooled spindle motor with 4pcs ceramic ball bearings!

This powerful spindle motor is perfect for your CNC machine, providing smooth and precise cutting for all your projects. With 110 volts of power, you can trust this motor to deliver consistent performance and reliability.

The 4pcs ceramic ball bearings ensure smooth operation and extended durability, making this spindle motor a top choice for professionals and hobbyists alike.

Don’t settle for anything less than the best when it comes to your CNC machine – invest in the 2.2KW ER20 D80 110V Air cooled spindle motor today! #CNC #spindlemotor #precisioncutting
#2.2KW #ER20 #D80 #110V #Air #cooled #spindle #motor #4pcs #ceramic #ball #bearings #Volts