Price: $233.00
(as of Dec 03,2024 17:19:49 UTC – Details)

Product Description

0.8KW 110V WATER COOLED CNC SPINDLE MOTOR KIT

Package Include ( What you see is what you receive )

1 x 0.8KW Water Cooled Spindle Motor ER11
1 x 1.5KW VFD 110V
1 x 65mm Spindle Motor Mount
1 x 80W Water Pump 110V
1 x 5m Pipe
14 x ER11 Collet（1mm, 1.5mm, 2mm, 2.5mm, 3mm, 3.5mm, 4mm, 4.5mm, 5mm, 5.5mm, 6mm, 6.5mm, 7mm, 3.175mm）

Water Cooled Spindle Motor

Power: 800W
Voltage: 110V AC
Speed: 24000RPM
Current: 4A
Szie: 65x158mm
Frequency: 0-400Hz
Collet Size: ER11
Material: Stainless Steel
Accuracy: 0.003–0.005
Runout off: Less than 0.01mm

Variable Frequency Drive

Power: 1.5KW
Input Voltage: 110V(+/-15%)
Output Voltage: 110VAC
Input Frequency: 50-60 Hz
Output Frequency: 0-1000 Hz
Input Phase: 1 phase
Output Phase: 3 phase

65mm Spindle Motor Mount

Made of high quality cast aluminum, this spindle motor mount is strong and durable.
The surface is well finished by sand blast which ensures a better smoothness.
This bracket would be a great replacement for CNC parts.

Water Pump

Power: 80W
Voltage: 110V AC
Flow Rate: 3500L/H
Lift Height: 3.5M
Overall Dimension:153x88x108mm

5M Water Pump

With 5M water pump for 0.8KW spindle motor kit.

14pcs ER11 Collet

Size:1mm, 1.5mm, 2mm, 2.5mm, 3mm, 3.5mm, 4mm, 4.5mm, 5mm, 5.5mm, 6mm, 6.5mm, 7mm, 3.175mm(1/8″).
First class 1065 carbon steel
Hardened and precision ground
Made of high grade specially formulated spring steel

Applicable Engraving Materials

The Spindle motor is mainly suitable for NON-metallic engraving.For example: wood, plastic, acrylic, pvc, pcb, carbon fiber, density board and soft metal like copper, aluminum and the similar materials.

RATTMMOTOR CNC Spindle
High Quality Bearings

Using optimized bearings, this series of bearings has strong hardness and rust resistance, as well as dynamic balancing technology, the actual runout off of the spindle is close to 0.01 mm, the precision tapered bore is less than 0.005mm, high precision and durable.

Connect Spindle Motor to VFD

The wiring method of the spindle motor and the inverter is as follows:

VFD’s U= Spindle’s U1
VFD’s V= Spindle’s V1
VFD’s W= Spindle’s W1
Connect any 2pin terminal “R”, “S” or “T” of the inverter to “110VAC”.

Fuction keys description

RUN key: Run command
FOR/REV: Change the running director of motor
( DISP ) Shift key: Status monitor mode switch, parameter of third stage menu switch
SPEED: Speed controller
ESC: Return to the starus of “ENTER”
( ENTER ) SET Key: Enter into menu, enter into parameter or parameter date writing confirm
( UP ) Value change key: Parameter of fuction code, data increase, revise and select all kinds of modes
( DOWN ) Value change key: Parameter of fuction code, data decrease, revise and select all kinds of modes
STOP/RESET key: Stop command / abnormal command
LED display zone: Indicating for RUN, frequency, current, voltage, reverse

Description of control terminals / Description of jumper fuction:

Inverter wiring involves main circuit and control circuit. The user can raise the cover of housing, at this time main circuit terminal and control circuit shall be viewed, and the user conduct correct connection as per wiring circuit below.

X1, Set as forward during delivery
X2, Set as reverseduring delivery
X3, Set as reset during delivery
X4, Set as high speed during delivery
X5, Set as medium speed during delivery
X6, Set as low speed during delivery
GND, Digital/analog/communication and power earthing terminals, lsolation of GND inside from PE
P12, +12V power supply, Maximum output current 150mA
A11, Analog voltage input, Input voltage range:0-+10V

J1: Selection of X1-X6 wiring mode: NPN PNP ( Ex-factory setting: PNP)
J2: Selection of AO output: VO, voltage AO, current ( Ex-factory setting: VO)
J3: Selection of AI2 input: V, voltage A, current ( Ex-factory setting: A)
J4: RS485 communication interface terminator enabled: ON OFF ( Ex-factory setting: OFF)
J5: Selection of X6 terminal fuction reuse: X6 Y1-PEO ( Ex-factory setting: X6)

Specification of Protection Control:

Overload protection: Electric relay protection motor driver
Fuse protection: In case of fuse, the motor stops running
Over voltage / Low voltage
Restart after transient stop: Restart after transient stop through frequency tracking mode
Stall prevention: Stall prevention during acceleration/deceleration
Short circuit of output terminal: Electronic protection
Overheating protection of ridiating fin
Other fuctions: reverse limit, direct startup after operating, fault reset, parameter locking, ect.

Description of main circuit terminals:

L / N: Input power terminal, connected to singe-phase power
U / V / W: Input output terminal, connected to three-phase motor
DC+ / DC- : DC output + terminal, DC bus output terminal is used for connecting external brake unit or common DC bus system.
DB: Brake output terminal, connecting brake resistor between DB and DC+
PE: Earthing terminal, inverter housing earthing terminal must be earthed.

RATTMMOTOR 1.5KW 110V VFD

Frequency range: 0-1000Hz
Accuracy: 1) Digital type: 0.01％(-10～40℃); 2) Analog type: 0.1％(25±10℃)
Setting resolution: 1) Digital type: 0.01Hz; 2) Analog type: 1％ of the maximum operating frequency
Output resolution: 0.01Hz
Keyboard setting mode: Set directly
Analog setting mode: External voltage 0-5V, 0-10V, 4-20mA, 0-20mA
Other Ductions: 3 hopping frequencires (lower-frequency limit, start-up frequency and stop frequency) can be set respectively.
Control Mode: V/F Vector Control
Communication Control: RS-485
Vibration: Below 0.5G

【Package Include】: ①1 x 0.8KW Water Cooled Spindle Motor ER11 ②1 x 1.5KW VFD 110V③1 x 65mm Spindle Motor Mount ④1 x 80W Water Pump ⑤1 x 5m Pipe ⑥14 x ER11 Collet（1mm, 1.5mm, 2mm, 2.5mm, 3mm, 3.5mm, 4mm, 4.5mm, 5mm, 5.5mm, 6mm, 6.5mm, 7mm, 3.175mm）
【0.8KW Spindle Motor】: ①This is a 110V-0.8KW water-cooled 4A Φ 65x158mm spindle motor come with a ER11 nut and collet, and equipped with a 65mm spindle mount. Frequency is 400HZ, 0.003–0.005 accuracy and runout off is Less than 0.01mm. ②Speed of The Spindle Motor : 0-24000RPM. Because it is a high-speed spindle motor, the spindle speed must not be lower than 9000 rpm during the use of the spindle. It should be noted that the main shaft cannot only rotate clockwise or counter clockwise.
【VFD Inverter Parameters】The 1.5KW variable frequency drive inverter has five-digits display and status indicator lamp display frequency, current, revolution, voltage, counter, temperature, foward or reverse running, fault, ect. Input Voltage: 110V(+/-15%) ,Output Voltage 110V, Input Frequency: 50-60 Hz, Output Frequency: 0-1000 Hz, Input Phase: 1 phase, Output Phase: 3 phase.
【How to Connect Spindle Motor and VFD Inverter】The spindle motor’s aviation plug marked with number 1, 2, 3, 4. Number 1, 2, 3 port are connected separately with inverter’s port U, V, W. Number 4 is the ground wire, no wiring is required.
【80W 110V Water Pump】Power: 80W, Flow: 3500L/H, Hmax: 3.5M, Voltage: 110V/50HZ. Also suitable for 0.8KW, 1.5KW, 2.2KW, 3KW and other high speed CNC water cooled spindle motor. Please remind that the submersible pump should be completely immersed in water when it is working to ensure that the submersible pump has a certain degree of cooling.

Introducing the RATTMMOTOR 800W Water Cooled Spindle Kit!

Upgrade your CNC machine with this powerful 65mm spindle motor that packs a punch with 0.8KW of power. The water-cooled design ensures efficient cooling, allowing for longer cutting sessions and increased durability.

This kit includes a 1.5KW VFD (Variable Frequency Drive) that converts your 110V single-phase power supply to 3-phase, giving you precise control over spindle speed and performance.

Also included in the kit is a 65mm spindle mount, ER11 collet, and 80W water pump, providing everything you need for a complete installation.

Don’t settle for anything less than the best – revolutionize your CNC experience with the RATTMMOTOR 800W Water Cooled Spindle Kit. Order yours today and take your projects to the next level! #CNC #SpindleKit #UpgradeYourMachine
#RATTMMOTOR #800W #Water #Cooled #Spindle #Kit #65mm #Spindle #Motor #0.8KW #110V #400HZ1.5KW #VFD #110V #Single #Phase #Inverter #Variable #Frequency #Drive65mm #Spindle #MountER11 #Collet80W #Water #Pump #CNC