Tag: PrimoChill

Price: $39.95
(as of Dec 26,2024 22:28:42 UTC – Details)

Product Description

FULL DISCLOSURE AND IMPORTANCE IN PREP

PRIMOCHILL VUE IS A SHOW COOLANT FIRST

PrimoChill has gone to great lengths to make Vue as easy to use as possible, but please keep in mind that it is for EXPERIENCED USERS looking for that extra aesthetic and requires more attention and maintenance and any other coolant Adding Vue to the system also requires more work than just pouring it in, but a spotless loop and ZERO air inductions during filling the system will make for less overall headaches.

Vue has a HIGH attraction to dyes. It’s possible that it may leach old dyes out of components that had previously dyed coolants ran through them (radiators in particular). No amount of flushing with water will remove all previous dyes. This may result in Vue changing color slightly. For best results flush your system with PrimoChill System ReBoot prior to using VUE in existing systems that contained dyed coolant.

Sys Reboot is for loops that have seen coolant before dyed or not dyed. Reboot is effective at removing previous dyes from the loop, especially from the radiator. It also works very well on neutralizing some coolant additives that are left behind from previous coolants.

Features

Water Based

Handmade in Small Batches Unmatched Quality Control

Fluid with a Visual Indicator

Built in Safeguard for Longer Lasting Fluid

Step 1 – Prepping

If your system is brand new we recommend using both Rad Clean and Sys Prep. If you have existing system, utilize our Rad clean and then move to step 2.

Step 2 – Cleaning old fluid out

System Reboot was created to pull old dyes and fluid out of existing PC builds. This is essential to use if you had any other previous fluids in your build that you plan to use Vue in.

Step 3 – Final Prep and Protection

Primo Prep was created with Vue in mind. It has protective properties that help with both your Vue lasting longer and it’s ability to keep the same color throughout it’s duration.

Step 4 – Add your final Vue

After going through all the proper prepping (follow our guide) you’re ready to add your Vue!

VUE FILLING GUIDE

PrimoPrep was created with Vue in mind and should always be used when using Vue. The pre-treatment helps control the fluctuation of the PH levels in your system caused by high levels of copper typically due to large capacity radiators. With this treatment, it also prepares the system for use of coolants in a mix metal closed-loop leaving the guesswork a thing of the past. This is a MANDATORY prep if not your Vue will FAIL.

Slowly add the prep fluid to your loop and avoid letting air into the system to prevent bubbles from slowing down the process. The more bubbles the more flushes are needed. Fill the reservoir, cycling the pump and repeating the process until the loop is full. is normally the best practice, for prep and the final coolant. Address leaks immediately, and if there are flow issues look at the entire loop to make sure that the coolant is flowing in the correct direction. Now it is time to let the system work its magic. We recommend running the prep for 24 – 48 hours. You may use the system during this process. After the waiting period is over, drain the system and inspect the loop for any debris that may have dislodged during the flush. If all looks well it is time to do a final rinse.
Rinse the system until the water runs clear and is bubble-free. Next, drain the system completely. The goal is to get out as much leftover fluid. Tipping the system over, back to back, and upside down will help free any fluid hiding in corners of blocks and in tops or ends of radiators. You may be surprised by how much fluid remains, so take your time.
Slowly add the coolant and fill the reservoir ¾ of the way before cycling the pump. Cycle the pump for five seconds, or until the water level drops on the reservoir to ¼. Stop and refill the reservoir ¾ of the way and cycle the pump again. Continue to do this until the loop is “bled” of air and residue fluid. Once the system is bled it should be very quiet. If you here churning, knocking and bubbling then there is still air in the system. Once it is quiet, put the cap back on the reservoir and top is all the way off through the port in the top. This process should take 2-3 hours depending on the size of your loop and it’s complexity.

PRO TIPS

1. Running your pump at a slow RPM/speed will help keep your Vue together. Running at high speeds will create a shearing effect on the exist of the pump and inlet and outlets of water blocks. The shear is essentially ripping apart all the goodies inside your Vue coolant. You will start to see a collection of white residue on the inside of the tubes if so time to crank down the pump speed.

2. Almost every case on the market has room to mount a radiator to the top of your case. When using this mount it can cause issues with Vue if you do not properly bleed all of the air out of that radiator. Take your time and tilt/rock your case back and forth and side to side so any air trapped in the radiator will hopefully get forced out. This can time a little bit of time so go slow and keep an eye out for bubbles.

PC Ice

Difficulty
Expert
Intermediate
Intermediate
Beginner
Beginner

Fluid Type
Show Fluid (performance properties)
Performance Fluid
Performance Fluid
Performance Fluid
Performance Fluid

Available Colors
25
25

Recommended for Daily Use

✓
✓
✓
✓

Conductivity
Low
Low
Low
Low
Low

Water Based
✓
✓
✓
✓
✓

NON COMPATIBLE HARDWARE FOR VUE

ALUMINUM WATER-COOLING COMPONENTS | Aluminum water-cooling components are not compatible with Vue as over a brief period Vue breaks apart and loses all Vue effects.
SILVER COILS, SILVER COMPONENTS, SILVER PLATED COMPONENTS | Silver Coils, Silver components, and Silver plated components are not compatible with Vue as the release of silver from these sources break the structure of Vue and will cause the fluid to lose all effects.
ADDITION FLUIDS | Addition of water, dyes, or other preps will cause Vue to break down as the chemical balance in Vue is altered with the addition of any of these. If you need to top of your loop then it needs to be topped off with Vue of the same color. Do not mix assorted colors of Vue as each color is balanced to specific levels that should not be altered.
ANY FITTINGS THAT HAVE A NON-NICKEL INTERIOR FINISH | It’s important to choose the right set of fittings as Vue and the interior of each fitting make contact. Always choose a fitting that has a nickel finish inside. Stay away from non nickel finishes and interior painted fittings as this can cause Vue to breakdown.
BAY RESERVOIRS | Bay reservoirs pose a difficult challenge for Vue as some manufactures require a gap of air to remain in the reservoir for it to function properly. Any additional air introduced to a loop running Vue will cause Vue to breakdown overtime.
ALWAYS CHECK | with manufactures website for updated compatibility issues. www keepingit cool/vue

Released in 2017, Vue has withstood the test of time and is still a favorite SHOW COOLANT in the watercooling community with its unique visual traits, Vue is sure to bring another dimension to any loop.
Vue’s exclusive water-based formulation allows it to stay suspended longer allowing longevity.
Safe to use with all rubber gaskets, acrylic tubing, pvc tubing, petg tubing, glass tubing, as well as nickel and copper components.
Pre-Dyed and handmade in small batches for unmatched quality control right here in Boise, ID USA
Vue’s visual indicator is useful to illustrate fluids flow patterns in your watercooling loop or product design.

Introducing the PrimoChill Vue Pre-Mix (32oz) – Computer WaterCooling Fluid in the vibrant and eye-catching shade of Toxic Candy!

This fluid is not only designed to keep your computer running smoothly and efficiently, but it also adds a pop of color to your water cooling system. The Toxic Candy hue is perfect for those who want to make a statement with their PC build.

Not only does this fluid look great, but it also provides excellent thermal conductivity and corrosion protection for your components. With its non-toxic, non-flammable formula, you can trust that your system will stay cool and safe.

Upgrade your water cooling system with the PrimoChill Vue Pre-Mix in Toxic Candy and take your PC build to the next level! Available now for purchase.

#PrimoChill #WaterCooling #ToxicCandy #PCBuild #TechEnthusiast
#PrimoChill #Vue #PreMix #32oz #Computer #WaterCooling #Fluid #Toxic #Candy,water cooling
pc